Printronix L1524 Manuel d'utilisateur Page 82
- Page / 148
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
3–42 Configuring the Printer
The printer completes each print job by fusing the toner on the last page and
advancing the last page to exit the printer. To print the next job, the printer must
retract the paper from outside the printer to prevent white space (blank pages)
from occurring between printed pages. This is the normal printing mode (default).
Some types of media can snag when retracted into the printer.
NOTE: Set the No Retract Mode to Enable to prevent paper from retracting
into the printer.
Ignore Errors
If Enabled, the printer will ignore minor paper motion errors when they occur
while printing. Paper jams and critical errors will continue to be reported. If
disabled, the printer will report all errors when they occur.
Check TOF Lever
Default is Disabled. In this mode, the printer will signal the user to check the TOF
lever. If enabled, the printer will not signal the user to check the TOF lever.
NOTE: Set to Enable if False “09 Check TOF Lever” error messages occur
while printing.
Paper Control Error
Default is Enabled. In this mode paper control errors will not be reported by the
printer. If Disabled, paper control errors will be reported by the printer.
NOTE: Set to Disable if paper jams occur in the fuser area but are not
detected and reported.
- 1
- Software License Agreement 2
- 3
- Communication Notices 4
- Trademark Acknowledgments 6
- Table of Contents 7
- Operator Calls 4–4 10
- Critical Error Messages 4–5 10
- Introduction 11
- About This Manual 12
- The Printer 14
- Printer Features 15
- Hardware Options 16
- Fonts and Forms 16
- Setting Up the Printer 19
- Safety Precautions 20
- Select a Site 22
- Unpack the Printer 24
- Initial Setup 25
- Add the Starter Toner 26
- Starter Toner Bottle 27
- (with spout attached) 27
- Developer Unit Cover 27
- (shown in the open position) 27
- Install the Ozone Filter 28
- 2–12 Setting Up the Printer 30
- Fuser Cleaner 31
- Felt Cover (shown 31
- Fuser Cleaner Felt 31
- Install the OPC Drum Unit 32
- Load Paper 33
- 2–16 Setting Up the Printer 34
- Figure 2–9. Loading Paper 34
- Cable Connections 35
- Powering On The Printer 36
- Check for Interference 38
- Transporting the Printer 38
- Long Distance Transport 39
- 2–22 Setting Up the Printer 40
- Configuring the Printer 41
- Changing Printer Settings 45
- Saving a Configuration 46
- Modifying a Configuration 48
- Printing a Configuration 51
- Factory Settings 52
- 3–13Configuring the Printer 53
- 3–14 Configuring the Printer 54
- Configuration Menus 55
- Configuration Menu Overview 56
- Config Control Menu 57
- Load Configuration 58
- Save Configuration 58
- Print Configuration 58
- Delete Configuration 59
- Power-Up Configuration 59
- Protect Configs 59
- Name Configs 59
- Programmer’s Reference Manual 60
- PhoenixPage 61
- Host Interface Menu 62
- Auto Switching 63
- Port Type 64
- Trickle Time 64
- Time Out 64
- Report Status 64
- Host Interface: Centronics 65
- Host Interface: Dataproducts 67
- Data Polarity 68
- Resp. Polarity 68
- Latch On Data 68
- Prime Signal 68
- PI Ignored 68
- TOF Action 69
- Buffer Size In K 69
- Host Interface: Serial 70
- XON/XOFF (default) 71
- SERIES 1, 1 CH 71
- SERIES 1, 2 CH 72
- Baud Rate 73
- Word Length 73
- Stop Bits 73
- Data Term Ready 74
- Request To Send 74
- Poll Character 75
- Poll Response 75
- Idle Response 76
- One Char Enquiry 76
- Ethernet Parameters Menu 78
- Paper Control Menu 79
- Horizontal Image Shift 80
- Vertical Image Shift 80
- Reprint on Fault 80
- Printer Control Menu 81
- Ignore Errors 82
- Maint./Misc.Menu 83
- Panel Key Sound 84
- Power-up State 84
- Hex Dump Mode 84
- PTX Setup Option 85
- Display Language 85
- Downloaded Fonts 86
- File System 86
- Font Memory Menu 87
- Maximum Cached Char 88
- Standard Chars 88
- Bold Chars 88
- Engine Life Data 89
- System Info 90
- Loading Flash Memory 90
- The CNVT2FLS Utility Program 91
- Downloading into Flash Memory 94
- Printnet 94
- User’s Manual 94
- <Return> 98
- 3–64 Configuring the Printer 104
- Chapter Contents 105
- Printer Diagnostics 106
- Operator’s Guide 107
- Error Messages 108
- Operator’s 109
- Message Problem 110
- Specifications 111
- Controller 112
- Electrical 112
- Power Consumption 113
- Dimensions 113
- Environment 113
- ° to + 90° F 113
- Printing 113
- Interfaces 114
- Emulations 114
- Font and Character Sets 114
- Host I/O Interfaces 117
- Termination Resistors 122
- RS–232 Serial Interface 123
- RS–422 Serial Interface 125
- IEEE 1284 Parallel Interface 126
- Compatibility Mode 127
- Nibble Mode 127
- Byte Mode 127
- Diagnostic Port 131
- Media Requirements 133
- Acronym for 135
- Contraction of 135
- PRINTRONIX, INC 148
- PRINTRONIX 148
Produits connexes et manuels pour Imprimeurs Printronix L1524
(5 pages)
(34 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.184 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels