Printronix L1524 Manuel d'utilisateur Page 121
- Page / 148
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
B–5
Host I/O Interfaces
NOTE: The printer comes standard with 470/1K ohm terminator resistors.
Verify host computer port termination resistor requirements. In most
cases, Dataproducts requires 220/330 ohm termination resistors.
Optional termination resistors are available from your service
provider.
Dataproducts Parallel Interface Signals
The Dataproducts interface signals are defined below.
READY
– A high true signal from the printer indicating AC power and DC
voltages are present, paper is loaded properly, and the printer is not in a fault
condition.
ON LINE – A high true signal from the printer indicating the Ready Line is true
and the ON LINE switch on the control panel has been activated. The printer is
ready to accept data from the host.
DAT
A REQUEST
– A high true signal from the printer to synchronize host data
transmission with printer timing. This signal goes true when the printer is ready to
receive data. It changes to the false state shortly after the leading edge of the
data strobe signal.
DATA STROBE – A high true pulse from the host to indicate that data is ready.
The data strobe must remain high at least until the Data Request line goes false.
DATA LINES – Eight standard or inverted levels from the host that specify
character data, plot data, or a control code. Sensing Data Line 8 is controlled by
printer configuration.
P
APER INST
– Optional standard or inverted level VFU signal from the host with
the same timing and polarity as the data lines. PI line sensing is controlled by
printer configuration.
NOTE: The PAPER INST Line must be disabled (configuration option
selected from the front panel) if the host computer does not drive or
control the PI Line. If the line is not controlled by the host and
sensing is enabled, rapid paper slewing will occur.
Interface Verification – Two pins on the interface connector jumpered together
allow you to verify proper installation of the interface connector.
- 1
- Software License Agreement 2
- 3
- Communication Notices 4
- Trademark Acknowledgments 6
- Table of Contents 7
- Operator Calls 4–4 10
- Critical Error Messages 4–5 10
- Introduction 11
- About This Manual 12
- The Printer 14
- Printer Features 15
- Hardware Options 16
- Fonts and Forms 16
- Setting Up the Printer 19
- Safety Precautions 20
- Select a Site 22
- Unpack the Printer 24
- Initial Setup 25
- Add the Starter Toner 26
- Starter Toner Bottle 27
- (with spout attached) 27
- Developer Unit Cover 27
- (shown in the open position) 27
- Install the Ozone Filter 28
- 2–12 Setting Up the Printer 30
- Fuser Cleaner 31
- Felt Cover (shown 31
- Fuser Cleaner Felt 31
- Install the OPC Drum Unit 32
- Load Paper 33
- 2–16 Setting Up the Printer 34
- Figure 2–9. Loading Paper 34
- Cable Connections 35
- Powering On The Printer 36
- Check for Interference 38
- Transporting the Printer 38
- Long Distance Transport 39
- 2–22 Setting Up the Printer 40
- Configuring the Printer 41
- Changing Printer Settings 45
- Saving a Configuration 46
- Modifying a Configuration 48
- Printing a Configuration 51
- Factory Settings 52
- 3–13Configuring the Printer 53
- 3–14 Configuring the Printer 54
- Configuration Menus 55
- Configuration Menu Overview 56
- Config Control Menu 57
- Load Configuration 58
- Save Configuration 58
- Print Configuration 58
- Delete Configuration 59
- Power-Up Configuration 59
- Protect Configs 59
- Name Configs 59
- Programmer’s Reference Manual 60
- PhoenixPage 61
- Host Interface Menu 62
- Auto Switching 63
- Port Type 64
- Trickle Time 64
- Time Out 64
- Report Status 64
- Host Interface: Centronics 65
- Host Interface: Dataproducts 67
- Data Polarity 68
- Resp. Polarity 68
- Latch On Data 68
- Prime Signal 68
- PI Ignored 68
- TOF Action 69
- Buffer Size In K 69
- Host Interface: Serial 70
- XON/XOFF (default) 71
- SERIES 1, 1 CH 71
- SERIES 1, 2 CH 72
- Baud Rate 73
- Word Length 73
- Stop Bits 73
- Data Term Ready 74
- Request To Send 74
- Poll Character 75
- Poll Response 75
- Idle Response 76
- One Char Enquiry 76
- Ethernet Parameters Menu 78
- Paper Control Menu 79
- Horizontal Image Shift 80
- Vertical Image Shift 80
- Reprint on Fault 80
- Printer Control Menu 81
- Ignore Errors 82
- Maint./Misc.Menu 83
- Panel Key Sound 84
- Power-up State 84
- Hex Dump Mode 84
- PTX Setup Option 85
- Display Language 85
- Downloaded Fonts 86
- File System 86
- Font Memory Menu 87
- Maximum Cached Char 88
- Standard Chars 88
- Bold Chars 88
- Engine Life Data 89
- System Info 90
- Loading Flash Memory 90
- The CNVT2FLS Utility Program 91
- Downloading into Flash Memory 94
- Printnet 94
- User’s Manual 94
- <Return> 98
- 3–64 Configuring the Printer 104
- Chapter Contents 105
- Printer Diagnostics 106
- Operator’s Guide 107
- Error Messages 108
- Operator’s 109
- Message Problem 110
- Specifications 111
- Controller 112
- Electrical 112
- Power Consumption 113
- Dimensions 113
- Environment 113
- ° to + 90° F 113
- Printing 113
- Interfaces 114
- Emulations 114
- Font and Character Sets 114
- Host I/O Interfaces 117
- Termination Resistors 122
- RS–232 Serial Interface 123
- RS–422 Serial Interface 125
- IEEE 1284 Parallel Interface 126
- Compatibility Mode 127
- Nibble Mode 127
- Byte Mode 127
- Diagnostic Port 131
- Media Requirements 133
- Acronym for 135
- Contraction of 135
- PRINTRONIX, INC 148
- PRINTRONIX 148
Produits connexes et manuels pour Imprimeurs Printronix L1524
(5 pages)
(34 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.650 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels