Printronix L1524 Manuel d'utilisateur Page 84
- Page / 148
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
3–44 Configuring the Printer
Panel Key Sound
Values: On (default) and Off
This option allows you to configure the printer to beep when you press a key
(switch).
Alarm
Values: On (default) and Off
This option allows you to configure the printer to beep when a printer fault
condition occurs.
Power-up State
Values: Online (default) and Offline
This option allows you to configure the printer to power-up in the offline or online
state.
Hex Dump Mode
Values: Disable (default) and Enable
This option allows you to place the printer into the “hex dump” mode, in which the
printer will output a hexadecimal data stream.
When enabled, the hex dump mode translates all host interface data to its
hexadecimal equivalent, then prints the hex code and its printable symbol, if one
exists. Figure 3–13 shows a partial example of a hex dump.
All characters printed after entering the hex dump mode (including any in the
input buffer) are printed in two forms: as a two-symbol hexadecimal code and as
its printable symbol, if any. A non-printable code is printed as a period [.] symbol.
Up to 16 characters can be printed per line. No control codes will be acted upon
by the printer while in hex dump mode.
The 16 characters are formatted so that the 16 printable symbols are printed in
columns 1 through 16. The 17th column is blank. Column 18 contains either a “p”
(PI line active) or a blank (PI not active). Columns 19 and 20 contain the
hexadecimal code for the first character, followed by a blank. The PI line
condition and hexadecimal code for the second character is printed in columns
22, 23, and 24, followed by a blank. The hexadecimal code for the 16th character
is printed in columns 78, 79, and 80.
- 1
- Software License Agreement 2
- 3
- Communication Notices 4
- Trademark Acknowledgments 6
- Table of Contents 7
- Operator Calls 4–4 10
- Critical Error Messages 4–5 10
- Introduction 11
- About This Manual 12
- The Printer 14
- Printer Features 15
- Hardware Options 16
- Fonts and Forms 16
- Setting Up the Printer 19
- Safety Precautions 20
- Select a Site 22
- Unpack the Printer 24
- Initial Setup 25
- Add the Starter Toner 26
- Starter Toner Bottle 27
- (with spout attached) 27
- Developer Unit Cover 27
- (shown in the open position) 27
- Install the Ozone Filter 28
- 2–12 Setting Up the Printer 30
- Fuser Cleaner 31
- Felt Cover (shown 31
- Fuser Cleaner Felt 31
- Install the OPC Drum Unit 32
- Load Paper 33
- 2–16 Setting Up the Printer 34
- Figure 2–9. Loading Paper 34
- Cable Connections 35
- Powering On The Printer 36
- Check for Interference 38
- Transporting the Printer 38
- Long Distance Transport 39
- 2–22 Setting Up the Printer 40
- Configuring the Printer 41
- Changing Printer Settings 45
- Saving a Configuration 46
- Modifying a Configuration 48
- Printing a Configuration 51
- Factory Settings 52
- 3–13Configuring the Printer 53
- 3–14 Configuring the Printer 54
- Configuration Menus 55
- Configuration Menu Overview 56
- Config Control Menu 57
- Load Configuration 58
- Save Configuration 58
- Print Configuration 58
- Delete Configuration 59
- Power-Up Configuration 59
- Protect Configs 59
- Name Configs 59
- Programmer’s Reference Manual 60
- PhoenixPage 61
- Host Interface Menu 62
- Auto Switching 63
- Port Type 64
- Trickle Time 64
- Time Out 64
- Report Status 64
- Host Interface: Centronics 65
- Host Interface: Dataproducts 67
- Data Polarity 68
- Resp. Polarity 68
- Latch On Data 68
- Prime Signal 68
- PI Ignored 68
- TOF Action 69
- Buffer Size In K 69
- Host Interface: Serial 70
- XON/XOFF (default) 71
- SERIES 1, 1 CH 71
- SERIES 1, 2 CH 72
- Baud Rate 73
- Word Length 73
- Stop Bits 73
- Data Term Ready 74
- Request To Send 74
- Poll Character 75
- Poll Response 75
- Idle Response 76
- One Char Enquiry 76
- Ethernet Parameters Menu 78
- Paper Control Menu 79
- Horizontal Image Shift 80
- Vertical Image Shift 80
- Reprint on Fault 80
- Printer Control Menu 81
- Ignore Errors 82
- Maint./Misc.Menu 83
- Panel Key Sound 84
- Power-up State 84
- Hex Dump Mode 84
- PTX Setup Option 85
- Display Language 85
- Downloaded Fonts 86
- File System 86
- Font Memory Menu 87
- Maximum Cached Char 88
- Standard Chars 88
- Bold Chars 88
- Engine Life Data 89
- System Info 90
- Loading Flash Memory 90
- The CNVT2FLS Utility Program 91
- Downloading into Flash Memory 94
- Printnet 94
- User’s Manual 94
- <Return> 98
- 3–64 Configuring the Printer 104
- Chapter Contents 105
- Printer Diagnostics 106
- Operator’s Guide 107
- Error Messages 108
- Operator’s 109
- Message Problem 110
- Specifications 111
- Controller 112
- Electrical 112
- Power Consumption 113
- Dimensions 113
- Environment 113
- ° to + 90° F 113
- Printing 113
- Interfaces 114
- Emulations 114
- Font and Character Sets 114
- Host I/O Interfaces 117
- Termination Resistors 122
- RS–232 Serial Interface 123
- RS–422 Serial Interface 125
- IEEE 1284 Parallel Interface 126
- Compatibility Mode 127
- Nibble Mode 127
- Byte Mode 127
- Diagnostic Port 131
- Media Requirements 133
- Acronym for 135
- Contraction of 135
- PRINTRONIX, INC 148
- PRINTRONIX 148
Produits connexes et manuels pour Imprimeurs Printronix L1524
(5 pages)
(34 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.021 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels