Printronix L1524 Manuel d'utilisateur Page 22
- Page / 148
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
2–4 Setting Up the Printer
The printer must be connected to an acceptable AC power source; otherwise, the
printer will not operate properly and may be damaged. The rear side panel label
identifies the correct power source for the printer: either 100 to 120 VAC, 60 Hz
(90 to 132 VAC, 47 to 63 Hz, 14 Amp) or 220 to 240 VAC, 50 Hz (198 to 264
VAC, 47 to 63 Hz, 7 Amp).
The power source must be properly grounded. Since large power fluctuations can
cause the printer to malfunction, it should be connected to a “noise–free” power
source, not subject to surges or noise generated by motors, lighting, or air
conditioning equipment on the same circuit. To allow for an adequate power
cable run, the printer should be placed no more than eight feet (2.5 meters) from
the power outlet.
Select a Site
When selecting the location for the printer, consider the following power
requirements, interface requirements, and environmental factors:
• A proper power source must be available. (Complete power
requirements are specified in the “Check Power Requirements” section
on page 2–3.)
• The location must be within the maximum cable length specifications for
the host computer interface.
• The temperature range should be +50
°F (10°C) to +90°F (32°C), with no
sudden changes in temperature or humidity. The printer should be
positioned away from any air drafts from heating or air conditioning
ducts.
• Insure that the room provides adequate ventilation. The minimum room
volume is 1000 cubic feet and must provide, at a minimum, one fresh air
exchange every two hours.
• The location should provide enough space for maintenance and
replacement of consumables (toner, developer, paper, etc.). Refer to
Figure 2–1.
• The printer should not be exposed to direct sunlight or hot lighting
equipment. This may cause an abnormal temperature rise in the printer
and adversely affect its operation. If necessary, shade or screen the
printer from such exposure.
• Avoid exposing the printer to any corrosive gases or vapors.
• Avoid installing the printer in an area subject to heavy vibrations.
For additional environmental requirements, refer to the “Introduction” chapter and
to Appendix A
.
- 1
- Software License Agreement 2
- 3
- Communication Notices 4
- Trademark Acknowledgments 6
- Table of Contents 7
- Operator Calls 4–4 10
- Critical Error Messages 4–5 10
- Introduction 11
- About This Manual 12
- The Printer 14
- Printer Features 15
- Hardware Options 16
- Fonts and Forms 16
- Setting Up the Printer 19
- Safety Precautions 20
- Select a Site 22
- Unpack the Printer 24
- Initial Setup 25
- Add the Starter Toner 26
- Starter Toner Bottle 27
- (with spout attached) 27
- Developer Unit Cover 27
- (shown in the open position) 27
- Install the Ozone Filter 28
- 2–12 Setting Up the Printer 30
- Fuser Cleaner 31
- Felt Cover (shown 31
- Fuser Cleaner Felt 31
- Install the OPC Drum Unit 32
- Load Paper 33
- 2–16 Setting Up the Printer 34
- Figure 2–9. Loading Paper 34
- Cable Connections 35
- Powering On The Printer 36
- Check for Interference 38
- Transporting the Printer 38
- Long Distance Transport 39
- 2–22 Setting Up the Printer 40
- Configuring the Printer 41
- Changing Printer Settings 45
- Saving a Configuration 46
- Modifying a Configuration 48
- Printing a Configuration 51
- Factory Settings 52
- 3–13Configuring the Printer 53
- 3–14 Configuring the Printer 54
- Configuration Menus 55
- Configuration Menu Overview 56
- Config Control Menu 57
- Load Configuration 58
- Save Configuration 58
- Print Configuration 58
- Delete Configuration 59
- Power-Up Configuration 59
- Protect Configs 59
- Name Configs 59
- Programmer’s Reference Manual 60
- PhoenixPage 61
- Host Interface Menu 62
- Auto Switching 63
- Port Type 64
- Trickle Time 64
- Time Out 64
- Report Status 64
- Host Interface: Centronics 65
- Host Interface: Dataproducts 67
- Data Polarity 68
- Resp. Polarity 68
- Latch On Data 68
- Prime Signal 68
- PI Ignored 68
- TOF Action 69
- Buffer Size In K 69
- Host Interface: Serial 70
- XON/XOFF (default) 71
- SERIES 1, 1 CH 71
- SERIES 1, 2 CH 72
- Baud Rate 73
- Word Length 73
- Stop Bits 73
- Data Term Ready 74
- Request To Send 74
- Poll Character 75
- Poll Response 75
- Idle Response 76
- One Char Enquiry 76
- Ethernet Parameters Menu 78
- Paper Control Menu 79
- Horizontal Image Shift 80
- Vertical Image Shift 80
- Reprint on Fault 80
- Printer Control Menu 81
- Ignore Errors 82
- Maint./Misc.Menu 83
- Panel Key Sound 84
- Power-up State 84
- Hex Dump Mode 84
- PTX Setup Option 85
- Display Language 85
- Downloaded Fonts 86
- File System 86
- Font Memory Menu 87
- Maximum Cached Char 88
- Standard Chars 88
- Bold Chars 88
- Engine Life Data 89
- System Info 90
- Loading Flash Memory 90
- The CNVT2FLS Utility Program 91
- Downloading into Flash Memory 94
- Printnet 94
- User’s Manual 94
- <Return> 98
- 3–64 Configuring the Printer 104
- Chapter Contents 105
- Printer Diagnostics 106
- Operator’s Guide 107
- Error Messages 108
- Operator’s 109
- Message Problem 110
- Specifications 111
- Controller 112
- Electrical 112
- Power Consumption 113
- Dimensions 113
- Environment 113
- ° to + 90° F 113
- Printing 113
- Interfaces 114
- Emulations 114
- Font and Character Sets 114
- Host I/O Interfaces 117
- Termination Resistors 122
- RS–232 Serial Interface 123
- RS–422 Serial Interface 125
- IEEE 1284 Parallel Interface 126
- Compatibility Mode 127
- Nibble Mode 127
- Byte Mode 127
- Diagnostic Port 131
- Media Requirements 133
- Acronym for 135
- Contraction of 135
- PRINTRONIX, INC 148
- PRINTRONIX 148
Produits connexes et manuels pour Imprimeurs Printronix L1524
(5 pages)
(34 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.758 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels